The Definitive Guide to Landscape Light Installation

The Definitive Guide to Landscape Light Installation

Blog Article

Not known Details About Landscape Light Installation

Without any type of significant electric experience I went on the hunt for very easy to install low voltage landscape lights. Reduced voltage landscape lights are powered via a transformer, that attaches to the cable, that decreases the voltage from regular 120 volts to 12 volts.


I always believed I would certainly need to dig ditches and run all sort of cables yet the low voltage outside limelights that I located were so easy to install. 30 minutes was all it required to offer our home a magical glow at night. I purchased 2 of these light sets for the front of our residence.


I probably could have managed with fewer lights however the 4 light collection was the tiniest one available. When I began looking for outdoor spotlights my first priority was to find something that was easy for me to install and hookup. After I narrowed down my choices I searched for lights that had terrific evaluations.






When I obtained them and laid the lights out I knew the 3 and 3 configuration would not work. Even though I obtained a lot of cable with the collection, I would have had to dig under the walkway in order to hide the cord.

Excitement About Landscape Light Installation

Bear in mind, I desired this to be very easy with no excavating and no rewiring. While I determined a repair I simply installed all 6 by the guest bed room to see just how they would certainly look. A quick word of caution. Although we are only connecting in lights it is essential to be risk-free and utilize care when dealing with electricity.


I simply stuck the risk right into the ground and adjusted the light. There was a black cable that ran to each spotlight so I rolled up the excess from each light and tie covered it using the black spin tie that came with the set.


Once the cables were hidden I plugged the limelights right into my exterior expansion cable, that is connected in to an outlet on the home. To make things even easier I also used a timer. Currently the landscape lights activate and off instantly at established times each night. Once the sun collection and my lights activated I went outside and adjusted them to hit the front of your house.


Like I stated, the smallest collection I could obtain was 4 lights so that's what I bought. Once they arrived I installed them adhering to the exact same steps as the very first set of lights.

Getting My Landscape Light Installation To Work

He wouldn't confess that I was right butI was right.


# 10 gauge outside cord # 12 scale outdoor cable 1-1/2 in. PVC pipe 1-1/2-in. PVC cap with -in.


Mount lights where they will not be easily damaged by plows or shovels. Keep in mind, as well, that the plants you light up will certainly undergo seasonal changes. Not all plants need to be evergreens, some plants such as hydrangea, dogwoods and sumac are fascinating lit up even when leafless. Once you have your materials, your tools and your plan, it's time to call 811.


It's a complimentary solution and you'll prevent unsafe and pricey shocks. Usage 10-gauge cord for the major lines from the transformer to where the lights start, after that change to 12-gauge cable between the lights. To bury the wires where they cross the lawn, use a flat-nosed shovel to cut a port and layer back the turf.

Everything about Landscape Light Installation

Because the transformer will always be connected in, you have to change the his response common electrical outlet cover with an in-use weatherproof cover, offered at many major home improvement facilities and hardware stores. The ground risks that include most upright illumination fixtures are not strong sufficient (or go deep sufficient) to keep them wonderful and straight with time with altering soil problems, disintegration, etc.


Using the PVC pipeline, construct and hide a footer that will certainly house the wire connections and sustain your post extensions (recommended to be made of 1/2- inch copper pipeline). Connect the wires with weatherproof cord ports. These wire adapters have a shield on the bottom and a ball of sealant inside that make them weatherproof.


Having a strong plan regarding landscape lights is more crucial than you could envision. Correctly illuminating locations in your yard and your home throughout the night not just provides a superb view of your residence however can additionally discourage possible mischief-makers or robbers. If you're unsure where to begin with landscape design lights, you're in the appropriate location! Below is our useful exterior lighting overview, where we will certainly walk with where to position landscape illumination, what sorts of lights to use, and exactly how to make use of light for the very best result.

The smart Trick of Landscape Light Installation That Nobody is Talking About

Set up lights where they will not be easily damaged by plows or shovels. Keep in mind, also, that the plants you brighten will undergo seasonal modifications. Not all plants need to be evergreens, some plants such as hydrangea, dogwoods and sumac are fascinating lit up even when leafless. Once you have your materials, your tools and your plan, it's time to call official website 811.


It's a cost-free solution and you'll stay clear of unsafe and pricey shocks. Usage 10-gauge cord for the major lines from the transformer to where the lights start, after that change to 12-gauge cable between the lights. look here To bury the wires where they cross the grass, make use of a flat-nosed shovel to reduce a port and layer back the sod.


Because the transformer will always be connected in, you have to change the common electrical outlet cover with an in-use weatherproof cover, offered at a lot of major home renovation facilities and hardware stores. The ground stakes that feature a lot of upright illumination fixtures are not solid sufficient (or go deep sufficient) to keep them wonderful and straight gradually with altering soil problems, disintegration, etc.


Using the PVC pipeline, construct and hide a footer that will house the cord links and support your post expansions (recommended to be made of 1/2- inch copper pipeline). Link the wires with weatherproof cord ports. These wire ports have a guard on the base and a blob of sealer inside that make them weatherproof.

Landscape Light Installation for Beginners

If you're not sure where to start with landscaping lights, you're in the ideal area! Below is our handy outdoor lighting guide, where we will walk with where to put landscape illumination, what kinds of lights to make use of, and just how to make use of light for the ideal result - Landscape Light Installation.

Report this page